Myalarm V-LCD1 Manuale delle Istruzioni Scaricare il pdf (Pagina 16)

QUICKSTART

2-10

System 2 Installation / Programming Manual

Card Reader Test

U Connect the reader using a short cable. Connect up both ports for a two door System 2. Figures 15- 24 show

the connections for the readers.

U The door lock could also be connected at this point. Figures 25-26 show the connections for door locks. If

System 2 is a two door unit two door locks can be installed.

U Enter a test Card:

Enter program mode by entering x12345# on the program keypad. The main menu should come up.

Enter Option #4 select card type - Press 4#. The Card Type prompt will display on the LCD.

Select a card type. Press 1-4 then #. You will return to the main menu.

Enter Option #5 port configuration - Press 5# . The Select Option prompt will display on the LCD.

Select option program ports. Press 1#. The Enter Port # prompt will display on the LCD.

Enter port number 1 - Press 1#. The Input Device(s) prompt will display on the LCD.

Enter the input device card only - Press 2#. The Relay Type prompt will display on the LCD.

Use the default relay type - Press #. The Momentary Time prompt will display on the LCD.

Use the default momentary time - Press #. The port schedule prompt will display on the LCD.

Use the default port schedule 0 - Press #. You will return to main menu.

Redo Option #5 if there is a second port. Change port number to 2.

Enter Option #8 Add or Change User. Press 8#. The Want to Continue prompt will display on the LCD.

Continue - Press 1#. The Enter User prompt will display on the LCD.

Enter user number 1 - Press 1#. The Press Any Key prompt will display on the LCD.

Press a key - Press #. The Enter Door ( 0 = Done) prompt will display on the LCD.

Enter door 1- Press 1#. The Enter Door ( 0 = Done) prompt will display again.

If there is a door 2 enter door 2 - Press 2#. The Enter Door ( 0 = Done) prompt will display again.

When all ports are entered enter 0 = done. Press 0#. The Enter Code Prompt will display on the LCD.

This prompt will be different for the different card types.

For Wiegand cards enter the facility code first then the five digit code number then the #. Do not enter any

leading zeros for the facility code. The outputs prompt will display

For Mag Stripe cards enter the code on the card then press #. You must enter any leading zeros. The outputs

prompt will display on the LCD.

For Data Chip touch a chip to the touch point at the upper right hand corner of the System 2 circuit board.

The Outputs prompt will display.

Use the default outputs - Press #. The Door 01 Schedule prompt will display.

Use the default door 01 schedule 0 - Press #. The Enter Anti-Passback prompt will display on the LCD

unless door 2 was selected. If door 2 was entered use the default door 2 schedule 0 - Press #. The Enter

Anti-Passback prompt will display on the LCD.

Use the default no anti-passback - Press #. The Enter Temporary Type prompt will display.

Use the default no temporary type - Press #. The Want to Continue prompt will display.

Do not continue - Press 2#. You will return to the main menu.

The test code is entered.

Go online- Press 0#. The Online event will be displayed on the LCD.

U Swipe the test card or touch the test Data Chip. The door relay should activate for 5 seconds and the Valid

User 1 event should be displayed on the LCD. If there are two doors swipe the test card or touch the test

Data Chip on both doors.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 335 336

Myalarm V-LCD1 Manuale delle Istruzioni Pagina 16

Commenti su questo manuale

Myalarm V-LCD1 Manuale delle Istruzioni Pagina 16

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Myalarm V-LCD1